Posts Tagged ‘Landenberg’

Water and Energy Saving Tips from Landenberg

Tuesday, October 11th, 2011

The cost of the heat, air conditioning and water supply to your Landenberg home continues to rise – it’s no wonder you want to cut your bills so much. But, how can you do that without cutting into the creature comforts and conveniences you’ve gotten used to over the course of the last few decades? Here are a few simple energy and water saving tips to make your life easier.

  • Patching Leaks – Two of the biggest wasters of water are dripping faucets and leaky pipes. The amount of water wasted by a single drip every second could provide for multiple baths per year – it adds up fast. Not only are leaky faucets and pipes easy to fix; they tend to develop into bigger problems as time passes.
  • Drains and Flushing – If you put a piece of toilet paper in the toilet used to clean an eye or wipe the counter, don’t flush. It’s a waste of water. If you notice some extra toothpaste in the sink, don’t rinse yet. You can always use the water from brushing your teeth or washing your face to clean it out. Multi-task and minimize how much water goes down the drain to save water.
  • Fully Loaded – A partially filled washing machine or dish washer is a huge waster of water. Fill it up and wait to run the device until it’s at the brim – the same amount of water is used no matter how much is in the device.
  • Compost vs. Disposal – A garbage disposal wastes a tremendous amount of water (if you want it to run properly). So, instead of churning the disposal up, create a compost pile and save a great deal of water/energy. If you have a septic tank, a garbage disposal is especially bad for your home as it can fill the tank up quickly with solids.
  • Insulate Pipes – Hot water pipes without insulation waste a tremendous volume of energy every year. The cost of running a hot water tank continuously every day can be anywhere from $200 to $300 per year, and that’s with insulation. Consider the cost without it to keep the water warm as it passes to your fixtures.
  • Lower Water Flow – Don’t crank your faucets up to the max just to get a glass of water or to check for hot water. It’s a waste of energy and it’s often unnecessary, especially when waiting for water to hit the right temperature.

If you’re interested in getting the most out of your home’s water supply, there are hundreds of little ways to save water that will add up over time. These are just some of the easiest ways to get started.

Tags: , , , , , ,
Posted in Energy Savings | Comments Off

Green Your Plumbing in Avondale

Friday, August 26th, 2011

These days, “green plumbing” is getting increasing attention, especially in Avondale.

“Green plumbing” helps the environment by doing one or more of the following:

  • Saving water
  • Saving energy
  • Using environmentally-friendly materials

There are a wide range of green plumbing products that can make a big difference in how much water and energy your home uses. They range from simple accessories that cost less than $20 to major home remodels. Here are a few of them, ranging from the simple and immediate to larger investments with a longer-term payback.

  • Low-flow showerheads and faucet accessories (often called “aerators”). Check the side of your current faucet and showerhead to see if they use more than 1.5 GPM and 2.0 GPM, respectively. If they do, you can benefit from an upgrade. Look for the EPA WaterSense label to be sure that your new showerheads and faucet accessories are water-efficient.
  • Hot water heater blankets and pipe insulation.You don’t need to insulate your hot water heater and  pipes to prevent freezing, but doing it will save money, water, and energy, and (as a bonus) you’ll enjoy hotter showers in the winter. This is a simple DIY job and the materials are extremely affordable.
  • Touch-free faucets. When you’re not actively using them, touch-free faucets shut off. According to industry estimates, the result can be a water savings of up to 70%. Touch-free faucet technology has improved greatly in recent years, and sensors are now very reliable. If you like your current faucet and want to keep it, there are also touch-free faucet conversion kits.
  • Dual-flush toilets. As the name suggests, these toilets have two different flushes: a “half-flush” for liquid waste, and a “full flush” for solids. Dual-flush toilets are standard in many European countries and are becoming increasingly popular in the U.S. because of their water-saving potential (up to 68% over conventional toilets) and sleek styling.
  • Tankless water heaters. Unlike conventional tank heaters, which use energy constantly to maintain a reserve supply of hot water, tankless heaters only use energy when hot water is needed.  Tankless water heaters are not quite “instantaneous”, as some manufacturers claim, but they provide hot water within a few seconds. Good quality heaters can provide hot water to multiple fixtures simultaneously.
  • Sprinkler system upgrades. Much of the water from spray sprinkler systems evaporates. Trickle and drip irrigation systems can improve water efficiency by delivering smaller amounts of water directly to the base of the plant. Other products, such as pressure regulating spray heads and rotors and automatic rain sensors, can also save thousands of gallons a year. Another option is to re-use laundry waste water by diverting it into the garden. This can be a DIY project or can be built directly into your plumbing. Check with your local authorities to find out if this is permitted in your area.

Tags: , , , ,
Posted in Water Conservation | Comments Off

How to Install a Toilet

Friday, July 29th, 2011

A toilet is a relatively basic piece of plumbing equipment, but that does not mean that installing it is easy. This is certainly a job that many people can do on their own, but you should be prepared to devoting the majority of your day to the project. While the installation itself is not terribly complicated, it is quite important that you get it right, so make sure you have all of the necessary materials, equipment and tools before you begin.

The first thing to remember is that you need to install your toilet in an appropriate place relative to the rest of your bathroom plumbing. Especially if you are installing your toilet along a branch drain, make sure that the sink, shower and any other plumbing fixtures are upstream of the spot where you will be installing the toilet.

You will also need to make sure that you install the toilet an appropriate distance from the wall. You need to be able to get around the toilet, and you also want to leave space so that work can be performed on the unit later. Putting your toilet too close to the wall can cause all kinds of complications in the way the unit functions and there is also a possibility of condensation build-up. For all of these reasons, it is important to make sure you are allowing an adequate amount of space on all sides.

The procedure you will have to follow when installing a toilet will be slightly different depending on whether you are installing it in a new spot or simply replacing an existing unit. When replacing an old toilet, you need to remove everything involved in the previous installation. That means taking the old bolts out of the floor and scraping away any residue to ensure that you have a clean and even surface to begin your installation on.

You should also make sure that you are aware of all applicable local codes before you begin your work. Even if you technically install your toilet correctly, you could run into trouble later on if your installation is not actually up to code. It is also important to remember to level all of your fixtures before you complete the installation process and to make sure you use a dielectric or brass fitting when attaching galvanized steel and copper to each other.

Tags: , , ,
Posted in Plumbing | Comments Off

How Can I Prevent Clogged Drains?

Wednesday, July 6th, 2011

One of the most frustrating plumbing issues any home owner will encounter is a clogged drain. Not only are clogged drains a nuisance, they are largely avoidable, so it becomes that much more frustrating when it happens since you know that you could have taken preventative measures long before the problem occurred. To help stop your drains from clogging in the future, here are some useful preventative tips:

  • Set Cooking Grease Aside – Cooking grease is thick, viscous and clings to the sides of almost all types of pipes. So, instead of pouring it down your sink and hoping it clears out on its own, pour it into a coffee can and set it aside. There are a number of places where you can recycle old grease.
  • Flush Garbage Disposals – When you use your garbage disposal, it is imperative that you flush cold water through the system at the same time. Without water to flush the food particles through the pipes, anything ground up in the disposal will become stuck and with the application of grease or other food particles can easily become a thick clog.
  • Pour Boiling Hot Water Down the Pipes – At least once a week it is a good idea to pour 2-3 quarts of boiling water down your sinks and bathtub to loosen any pre-clogs that have formed. Things like soap, grease, food, and hair can all be dislodged by an application of hot water on a regular basis.
  • Taking Care with Your Toilet – A toilet is not designed to flush anything that will technically fit down the hole. Even for paper products that seem to be flushable, take care in what goes into the toilet bowl. Paper towels, garbage, and wrappers should not be flushed or they are likely to cause clogs.
  • Use Strainers – Install strainers on all of your sinks, including the ones in your bathroom. A simple strainer will catch excess bits of food, hair, and other grime that has a habit of falling down the drain and getting flushed along with the dishwater or during a shower.

With care, your drains will remain clog free and never require the services of a snake or a plumber. If you do get past the point of no return, do not panic just yet – there are a number of steps you can take to remove a small clog without chemicals or professional help. However, if the clog refuses to budge or begins to backup, know when to call a plumber.

Tags: , , , , ,
Posted in Plumbing | Comments Off

How to Choose the Water Softener That Is Right for You

Friday, June 24th, 2011

If hard water is a problem in your home, the solution may be simpler than you think. There are many water softeners out there, and some of them can be quite effective at treating the water coming into your home in order to remove the minerals that make the water hard. However, there are plenty of distinct differences between the various products on the market as well, so you should take a closer look at your options before you commit to one system over another.

The first thing you need to know when you start looking at water softeners is how hard your water actually is. If your water is very hard, you will need a heavy duty water softener. But if there are only moderate amounts of calcium and magnesium in your water, you may be able to opt for a less powerful model.

You should also be aware of how much water you go through on a daily basis. You want to get a water softener big enough to handle the demands of your household, and you will not be able to do that if you do not know how much water you typically use.

Another difference between the various water softener models on the market today is the type of regeneration cycle they employ. You can opt for a timer regenerated water softener that will complete the regeneration cycle as often as you set it to. These models tend to be cheaper initially, but they can also cost more to operate and maintain in the long run because they will regenerate when the time comes whether it is actually necessary or not.

There are also meter regenerated water softeners that only go through a regeneration cycle once a certain volume of water has passed through them. These water softeners are specifically calibrated to the amount of calcium and magnesium you have in your water so they only go through a regeneration cycle when it is absolutely necessary.

One concern that many people have about using water softeners is that the most common types use sodium as a regeneration agent. That means that they exchange sodium for the calcium and magnesium in the water. If you need to limit your sodium intake, you may not want to be adding even this small amount to your water. In that case, you can purchase a water softener that uses potassium rather than sodium which can be just as effective at removing other minerals.

Tags: , , , ,
Posted in Plumbing | Comments Off