Posts Tagged ‘Kenton’

A Frederica Plumbing Tip: Why Is Your Toilet Dry and How Can You Fix It?

Wednesday, December 14th, 2011

Under normal circumstances, after you flush your toilet in your Frederica home, the tank and bowl both fill back up with water, preparing it for the next use. The water from the tank is what flushes into the bowl when you push the handle, so if it is not filling properly, then the toilet will be dry.

This problem is troublesome, but not uncommon. It has a number of possible causes and fixes.

The first place to look is the water supply to the tank. If it has been inadvertently turned off, then obviously the tank will not fill. This is akin to the troubleshooting section of your old VCR manual, where it tells you to make sure the power cord is plugged in. It may sound silly, but it never hurts to check the most obvious and easily fixed of the possible causes first.

Another possibility that is very easy to fix is that the ballcock inside the tank has jammed at the top. Inside your toilet tank is a rubberized bulb connected to an arm. This bulb floats in water and controls the intake valve on the toilet tank. So, when the water level reaches a certain depth, the ballcock floats and closes the valve. However, if the ballcock is jammed in an upward position, it would keep the valve closed even if the tank is empty.

In this case, it may just be a matter of pushing the ballcock past the jam and then making sure it moves up and down freely. That alone may fix it.

A third common cause of the dry toilet problem is a clogged intake valve beneath the toilet. These valves can become clogged and then not allow water through, especially in systems with hard water or particularly old pipes.

If this is the problem – or if it is anything besides one of the two simple fixes described above – the best solution is to call a plumber. A professional can correctly identify the source of the problem and perform the necessary repairs. It’s likely not going to be a huge repair, but it’s best to entrust the job to a pro.

Tags: , , , ,
Posted in Plumbing | Comments Off

Easy Drain and Sewer Maintenance: A Guide from a Greenville Plumber

Saturday, November 26th, 2011

When it comes to your Greenville home’s plumbing, one of the most important things you can do is perform regular drain and sewer maintenance. Those pipes are vital to maintaining a steady flow of waste water out of your home – if something goes wrong, you’ll regret not fixing it earlier. Here are some easy strategies for maintaining your drains and sewer lines:

  • Avoid Unflushable Items – Some items are designed to be flushed down the toilet. Everything else is not. If something isn’t specifically designed to go down your toilet, don’t put it down there. This includes paper towels, napkins, any kind of food, floss, or hair, and anything else that should go in a garbage can. Toilets may seemingly whisk everything away in one flush, but a lot of that stuff can get stuck on its trip to the sewer.
  • Clear Drains Weekly – You can’t clean your sewer line without professional help, but you can do your best to keep drains clear on their way out. Use boiling hot water and lemon juice or a mixture of baking soda and vinegar once a week to clear out the drains of any excess build up. Also, avoid putting any grease or other gunk down the drain that might stick to food particles and clog the drains.
  • Have Slow Drains Inspected – If a drain in your home slows down significantly, have it inspected. It might be a bit of hair stuck in a trap somewhere, or it could be your sewer line starting to clog. It’s better to know now than to wait and fall victim to a much larger problem in weeks or months.
  • Use Drain Strainers – Don’t let anything go directly down the drain. Use strainers to block food, hair or other stuff from getting into the sink or bathtub drains. Hair in particular, when mixed with grease or soap can become a glue-like substance in your drains.

Most drain and sewer maintenance is preventative and common sense. Pay attention to the effects your actions have on the water lines leaving your house and you can greatly reduce the risk that something goes wrong in the future.

Tags: , , , , ,
Posted in Plumbing | Comments Off

How to Clean Water Spots from a Shower Door: Some Pointers From Kenton

Friday, September 23rd, 2011

The relationship between water and your shower in your Kenton home is somewhat is paradoxical. You use the water in the shower to keep yourself clean, and you can use water to keep your shower (and everything else!) clean, but if left unchecked, the water itself will leave your shower dirty and spotty.

Those spots left on your shower door are mineral deposits from water that has evaporated, leaving its mineral passengers behind. They are especially problematic in areas with harder water. Here is how you can get rid of them.

The Natural Way

It may surprise you to know that with all the chemicals available on the market for cleaning the bathroom, the best remedies for hard water are actually natural ones: lemon juice and vinegar. They are both acidic, so they can dissolve the mineral deposits, and they rinse away clean.

To use lemon juice (or a lemon), apply it to a damp sponge and wipe the door. You can also squirt the lemon juice directly on the door and wipe it with a sponge. Use this technique and let the lemon juice soak in a bit for tougher stains. Your shower will not only be clean, but it will smell like lemons.

Although it doesn’t smell as nice as lemon juice, vinegar also works well. Don’t forget the cleaning power of vinegar and baking soda, which generates a powerful chemical reaction that helps break up tough stains. For water spots, mix up a paste of vinegar and baking soda. Use a small brush, like an old toothbrush, to spread the paste around the edges of the shower door and on any tough stains. Wipe it clean with a damp sponge.

You can also use vinegar or lemon juice weekly to keep tough deposits from building up.

Other Ideas

There are some other methods you can use if the spots are really stubborn. CLR, for example, can break up very stubborn mineral deposits, but it is also toxic, so use it sparingly. Daily shower cleaner sprays work well to stop water spots from forming if used regularly.

If you are worried that your water too hard (has too many minerals), you can always ask your plumber about a water treatment system.

Tags: , , , ,
Posted in Plumbing | Comments Off

How a Water Softener Works

Monday, June 27th, 2011

You use water for many things. It is necessary for bathing, cooking, washing clothes and for drinking. But the water we use in our homes is not pure. It has plenty of other minerals and additives suspended inside. While some of these, like fluoride, are intentionally added to the water supplies in certain areas, some others get in by chance.

Aside from actual pollutants, the additives you may be the most concerned about finding in your water are calcium and magnesium. These minerals are picked up by water as it moves through the ground, and the more of them that get into your home water supply, the harder that water will be.

The term hard water is used to describe water with high levels of calcium and magnesium present. These minerals are not actually dangerous to us, but they can cause all sorts of problems for your indoor plumbing and other household systems. For instance, hard water will leave deposits of these minerals on the insides of pipes and on sinks, faucets and bathtubs.

Residue will also build up in appliances like coffee makers, dish washers and washing machines. Over time these buildups can become a real problem and you may have to pay for costly repairs or need to replace large appliances.

In order to avoid these types of complications, your best bet is to have a water softener installed. These systems can be connected directly to your home water source and they are able to remove excess calcium and magnesium from the water before it ever reaches any of your indoor plumbing or appliances.

Water softeners generally remove these minerals by attracting the positively charged calcium and magnesium particles with a tank full of negatively charged polystyrene particles. In this system, the calcium and magnesium are replaced by sodium ions as they move through the water softener, thereby maintaining the overall balanced composition of the water. Once the water has passed through and the calcium and magnesium have been left behind, the water softener will flush them out and prepare to absorb another wave of hard water minerals.

Tags: , , ,
Posted in Plumbing | Comments Off