Posts Tagged ‘Frederica’

A Frederica Plumbing Tip: Why Is Your Toilet Dry and How Can You Fix It?

Wednesday, December 14th, 2011

Under normal circumstances, after you flush your toilet in your Frederica home, the tank and bowl both fill back up with water, preparing it for the next use. The water from the tank is what flushes into the bowl when you push the handle, so if it is not filling properly, then the toilet will be dry.

This problem is troublesome, but not uncommon. It has a number of possible causes and fixes.

The first place to look is the water supply to the tank. If it has been inadvertently turned off, then obviously the tank will not fill. This is akin to the troubleshooting section of your old VCR manual, where it tells you to make sure the power cord is plugged in. It may sound silly, but it never hurts to check the most obvious and easily fixed of the possible causes first.

Another possibility that is very easy to fix is that the ballcock inside the tank has jammed at the top. Inside your toilet tank is a rubberized bulb connected to an arm. This bulb floats in water and controls the intake valve on the toilet tank. So, when the water level reaches a certain depth, the ballcock floats and closes the valve. However, if the ballcock is jammed in an upward position, it would keep the valve closed even if the tank is empty.

In this case, it may just be a matter of pushing the ballcock past the jam and then making sure it moves up and down freely. That alone may fix it.

A third common cause of the dry toilet problem is a clogged intake valve beneath the toilet. These valves can become clogged and then not allow water through, especially in systems with hard water or particularly old pipes.

If this is the problem – or if it is anything besides one of the two simple fixes described above – the best solution is to call a plumber. A professional can correctly identify the source of the problem and perform the necessary repairs. It’s likely not going to be a huge repair, but it’s best to entrust the job to a pro.

Tags: , , , ,
Posted in Plumbing | Comments Off

Why Does My Garbage Disposal Leak, Grind Poorly and Make a Lot of Noise? A Question from Bear

Thursday, October 13th, 2011

It is definitely convenient to have a garbage disposal in your Bear home’s kitchen. They make doing the dishes and getting rid of food waste much easier. But just like any other appliance or piece of equipment in your home, your garbage disposal can sometimes develop a problem that causes it to leak or perform inadequately.

Leaky garbage disposals are certainly no fun to deal with. There are several reasons why garbage disposals can develop a leak. There could be an inadequate amount of putty or sealant at the joint where the garbage disposal connects to the drain pipe from the sink. A leak can also spring from that area simply because the bolts holding the two pieces together are not securely tightened.

The point where food and waste exit the garbage disposal and move into the main drainage system is another spot prone to developing leaks. These types of leaks are similar to those that occur between sink drain and garbage disposal and can be remedied in the same way.

In general, the key to dealing with a garbage disposal leak is to locate the source. This will most often be where two pipes come together or where the pipes join the unit. However, as your garbage disposal ages, it is more prone to developing cracks in the body of the unit itself. When this happens, leaks can develop anywhere there is a seam or break in the body of the garbage disposal itself. With this type of leak, the only thing to do is to replace the garbage disposal with a new one.

Leaks are not the only problems that can develop in a garbage disposal either. Sometimes you may notice that your garbage disposal is making an unusual amount of noise when it is turned on. This is often the result of something getting in there that should not have, so you should not continue to run your garbage disposal. Turn off all power to the unit and see if you can reach or see into the garbage disposal to determine what is causing the problem.

If your garbage disposal is not grinding well even though it seems to be rotating fine, you may not be running enough water into it when it is turned on. The water is necessary to facilitate the grinding process, so be sure to keep it going at all times. If that does not solve the problem, you may need to have a professional come out and take a look at your system to find out what is going on.

Tags: , , , , ,
Posted in Plumbing | Comments Off

Different Kinds of Plumbing Noises, Where They Come From and Why They Occur: A Guide From Hockessin

Thursday, September 1st, 2011

Under ideal conditions, you would hear nothing from your Hockessin home’s plumbing system except the sound of running water when you turn on the tap. Unfortunately, that is not always what actually happens. In fact, your plumbing can make all types of funny and sometimes alarming noises for no reason that you can easily discern.

For instance, one common plumbing noise sounds like a hard knock or hammer blow. This usually occurs when you turn off a tap and can be rather alarming. Sometimes you can even feel the reverberation of the impact that caused the sound. But why is this happening? Usually, this “water hammer” noise is the result of the dramatic shift in pressure in the system when you suddenly stop the flow of water from a faucet.

This sudden stop creates a kind of shock wave, which then travels back through the pipes and causes the loud knocking sound that you hear. This is easily fixed with a device that is known as a water hammer arrester. These devices help to dissipate the force of the pressure shift and can keep the noise from occurring at all.

There are also all kinds of whistling, squealing and squeaking noises that your plumbing can make under certain circumstances. These types of sounds are often caused by a worn out washer somewhere along the line that is having trouble regulating the flow of water. It can be a little difficult to pin down the source of these noises sometimes, especially if they occur no matter which faucet is turned on. But with a little hunting and trial and error you can usually track down the source.

Rattling sounds are also common and generally occur when your water pipes are not well secured to a rigid surface. If this is the case, the force of the water running through the pipes can cause the pipe to vibrate, creating the sound you hear as it bangs against whatever solid surface is nearby. For problems like this, simply securing the pipes in place better can put an end to all of your rattling issues.

If you need help fixing any of these problems, contact your local plumber.

Tags: , , ,
Posted in Plumbing | Comments Off

Signs of a Broken Water Line Outside the House: A Tip From Felton

Friday, August 5th, 2011

If you have a leaky pipe inside your Felton home, chances are you will notice it pretty quickly. Water seeping through the walls or the ceiling is a good indication that something is wrong and it is a hard thing to ignore. However, if there is a leak in your pipes outside of your home, it can be a bit harder to detect. Fortunately, there are some things you can keep an eye out for that will alert you if this does become a problem.

One of the first places to look for signs of a leak outside your home is your water bill. While your bill may not be exactly the same every month, chances are that it generally stays within a certain range. And if you use a ton of water one month for some reason, you will probably be aware of it. But if your water bill suddenly goes up for no reason that you can discern, there is reason to suspect that a leaky pipe somewhere is the culprit.

Keep in mind that unexplained puddles in your yard can also be an indication that a pipe underground is leaking. If you notice something like this, it is a good idea to call a professional plumber right away. Fixing underground pipe leaks is a challenging chore and requires special equipment that you most likely do not have lying around your home.

There are several reasons that leaks in your outdoor pipes can develop. For one thing, the pipes may be old or they may have been defective to begin with. Improper installation or shoddy workmanship can all lead to problems later on. As frustrating as it is, there is very little you can do except have the leaky pipes fixed.

Another possibility is that extreme temperatures have been damaging the pipes over time. Particularly if you live in an area with harsh winters, it is very possible that your pipes have frozen or come close to it from time to time. This constant exposure to freezing temperatures will take its toll even on the highest-quality pipes and eventually they will need to be replaced.

No matter what caused the problem, though, or how you realize that it exists, it is important to get leaky outdoor pipes fixed right away. The problem will only continue to get worse if you do not act.

Tags: , , , ,
Posted in Plumbing | Comments Off

Shower Installation: Prefabricated vs. Tile

Wednesday, July 27th, 2011

There are quite a few things to consider when you are choosing a type of shower installation. Whether you are simply redoing an older shower or are having a new one completely installed, you will have to decide whether you want to go with a prefabricated installation or a more traditional tile interior. Both of these types of installations have their own sets of advantages and disadvantages, so determining which one is right for you will have a good deal to do with the particulars of your situation.

Prefab installations are generally made out of fiberglass or acrylic, making them lighter and less expensive than the tile alternatives. This is always great if you are on a budget, and it can benefit you in other ways as well. For instance, if you are trying to install a shower in an area without substantial floor support, a prefab installation is ideal because the shower stall simply does not weigh that much.

But prefab shower installations also have their drawbacks. They are not as versatile, particularly the one-piece installations, and they are only available in a set number of sizes and styles. And while you can touch them up to a certain extent when cracks develop, the likelihood is higher that you will have to replace a prefab unit sooner than you would a tiled one.

Tiled shower installations are certainly more labor intensive to design and install. And this, of course, means that they cost more overall. But they also offer you a much wider range of design and installations possibilities. They can be made to fit any space and are especially convenient when you are remodeling your home because the materials used can easily be carried through spaces large and small.

If you are looking for a do-it-yourself project, however, a tile shower installation may not be for you. While it is possible to complete this type of project on your own, there are a lot of factors you will have to take into account. Also, the work takes much longer than a prefab installation would. The end result may be much more pleasing, but you will definitely have to work for it.

And even if you have professionals install your tile shower, it will take more than the one day the prefab installations usually take. So before you set your shower installation choice in stone, take some time to carefully consider the pros and cons of each.

Tags: , , ,
Posted in Plumbing | Comments Off

How Can I Prevent Clogged Drains?

Wednesday, July 6th, 2011

One of the most frustrating plumbing issues any home owner will encounter is a clogged drain. Not only are clogged drains a nuisance, they are largely avoidable, so it becomes that much more frustrating when it happens since you know that you could have taken preventative measures long before the problem occurred. To help stop your drains from clogging in the future, here are some useful preventative tips:

  • Set Cooking Grease Aside – Cooking grease is thick, viscous and clings to the sides of almost all types of pipes. So, instead of pouring it down your sink and hoping it clears out on its own, pour it into a coffee can and set it aside. There are a number of places where you can recycle old grease.
  • Flush Garbage Disposals – When you use your garbage disposal, it is imperative that you flush cold water through the system at the same time. Without water to flush the food particles through the pipes, anything ground up in the disposal will become stuck and with the application of grease or other food particles can easily become a thick clog.
  • Pour Boiling Hot Water Down the Pipes – At least once a week it is a good idea to pour 2-3 quarts of boiling water down your sinks and bathtub to loosen any pre-clogs that have formed. Things like soap, grease, food, and hair can all be dislodged by an application of hot water on a regular basis.
  • Taking Care with Your Toilet – A toilet is not designed to flush anything that will technically fit down the hole. Even for paper products that seem to be flushable, take care in what goes into the toilet bowl. Paper towels, garbage, and wrappers should not be flushed or they are likely to cause clogs.
  • Use Strainers – Install strainers on all of your sinks, including the ones in your bathroom. A simple strainer will catch excess bits of food, hair, and other grime that has a habit of falling down the drain and getting flushed along with the dishwater or during a shower.

With care, your drains will remain clog free and never require the services of a snake or a plumber. If you do get past the point of no return, do not panic just yet – there are a number of steps you can take to remove a small clog without chemicals or professional help. However, if the clog refuses to budge or begins to backup, know when to call a plumber.

Tags: , , , , ,
Posted in Plumbing | Comments Off